**** AGGREGATE FILE 74-25C.txt  5/17/01 ****

========================================================

    **** FILE 74B-25C.txt ****

These SED1374 register contents were taken while
displaying a 160x240x8 image on a KRS025EV0AC
Kyocera LCD module.  The SED1374 was on an
SDU1374BOC evaluation board by Epson.

CONNECTIONS
  This board was mounted in a ISA slot, connected to
  a special Kyocera KK5  interface board via a 40pin 
  cable.  The special KK5 has a unique 22 pin x 1mm
  pitch FFC connector for the special 1 mm pitch FFC
  required by this KRS025EV0AC.  The more typical
  KRS025EV0AB uses a 0.5 mm pitch FFC and would have 
  been connected to the connector of the KK5 No.1 
  labeled "CN4" on a white paper label. 

REGISTER CONFIGURATION  
  I made a copy of 1374BMP.EXE, renamed 74B-25C.EXE
  and ran 1374CFG.EXE to configure it as follows:

 PANEL TAB
 (The following settings are absolutely required
 by the Kyocera KRS025EV LCD modules)

    color, single, STN, 8bit, 160 x 240, format 2.

 (The following settings are within their range
  in the Kyocera specs for this LCD)

     FrameRate (fps)=76, InputClock (kHz)=7500.

 (The following settings are defaults that make
  the SDU1374 work.) 
      Mod Count = 0, LookUp Table = 4 BPP,
      MemoryLocation=0xD0000,
      FPLineStart=16, FPFrameStart=0, 
      FPline Hi, FPframe Hi, 
      Misc. Options all not checked.

 
SAVING CONFIGURATION VALUES
 Run 1374CFG.exe under windows.  To get the initial
 values, open 1374BMP.exe or a copy of it, for
 example 74B-25C.exe.  Then modify as above.  
   Then click "Save",
   highlight the same program you just opened, 
   Click "Save" and "Yes" to overwrite.

OPERATING THE LCD
 Run the program renamed 74B-25C.exe and configured 
 as above at the prompt on the MS-DOS emulation
 screen.  For example
    c:\...>74B-25C Co8-1624.bmp

REGISTER VALUES
 Below are the register contents resulting from
 this configuration, obtained by running 
 1374PLAY.exe at the MS-DOS, and entering 
 commands "xa", then "q".

     Robert Joslyn 3/23/2001  800-826-0527

==============================================

1374PLAY - test utility - version 1.00 (HAL 1.00)

=xa
=
[00] > 18  00011000b  024t	[01] > 23  00100011b  035t
[02] > C0  11000000b  192t	[03] > 03  00000011b  003t
[04] > 13  00010011b  019t	[05] > EF  11101111b  239t
[06] > 00  00000000b  000t	[07] > 00  00000000b  000t
[08] > 1A  00011010b  026t	[09] > 00  00000000b  000t
[0A] > 02  00000010b  002t	[0B] > 00  00000000b  000t
[0C] > 00  00000000b  000t	[0D] > 00  00000000b  000t
[0E] > 00  00000000b  000t	[0F] > 00  00000000b  000t
[10] > 00  00000000b  000t	[11] > 00  00000000b  000t
[12] > 00  00000000b  000t	[13] > FF  11111111b  255t
[14] > 03  00000011b  003t	[15] > 00  00000000b  000t
[16] > 00  00000000b  000t	[17] > 00  00000000b  000t
[18] > 00  00000000b  000t	[19] > 00  00000000b  000t
[1A] > 00  00000000b  000t	[1B] > 00  00000000b  000t
[1C] > 00  00000000b  000t
=q
=

================================================

    **** FILE 74-25pin.txt ****


Here is the connection table between Epson SED 1374 
controller IC  (not the eval board) and Kyocera 2.5 
inch 160x240 LCD modules (K*S025EV...)
I made this table from studying specifications.
I am fairly certain that is is correct but I
have not confirmed it by building a device. 


SED	SED		KC	KC
PIN	PIN		PIN	PIN
NAME	NO.		NO.	NAME

FPDAT0	37	=====	22	D0
FPDAT1	36	=====	21	D1
FPDAT2	35	=====	20	D2
FPDAT3	34	=====	19	D3
FPDAT4	33	=====	18	D4
FPDAT5	32	=====	17	D5
FPDAT6	31	=====	16	D6
FPDAT7	30	=====	15	D7
MOD	42	=====	8	DF
FPSHIFT	28	=====	3	CP
FPLINE	38	=====	2	LOAD
FPFRAM	39	=====	1	FRM

NOT DIRECTLY FROM SED IC
 enable		=====	4	DISP
 3.3 VDC logic	=====	5,6	VDD
 logic gnd	=====	7	VSS
 driving voltage
   plus bias	=====	9	V0
   ditto	=====	10	V1
   ditto	=====	11	V2
 driving ground
   plus bias	=====	12	V3
   ditto	=====	13	V4
   ditto	=====	14	V5

 Robert Joslyn 5/17/2001  800-826-0527

=========================================

    **** FILE 74B-25CP.txt ****

These SED1374 register contents were taken while
displaying a 240x160x4 image rotated 90 degrees
onto a KRS025EV0AC Kyocera LCD module.  The SED1374 
was on an SDU1374BOC evaluation board by Epson. 

The board and its SED1374 registers were configured 
exactly as described in 74B-25C.txt

However this test was executed as

  c:\...>74B-25C LA8-2416.bmp /P

The LCD was still 160x240.  74B-25C.exe was still
configured as 160x240 with no check mark in the
PortraitMode box.  But the image was 240x160 and 
the /P caused it to be rotated on the LCD. 

Below are the register values as rotated 
for comparison with 74B-25C.txt.

     Robert Joslyn 3/23/2001  800-826-0527

==============================================

1374PLAY - test utility - version 1.00 (HAL 1.00)

=xa
=
[00] > 18  00011000b  024t	[01] > 23  00100011b  035t
[02] > C0  11000000b  192t	[03] > 03  00000011b  003t
[04] > 13  00010011b  019t	[05] > EF  11101111b  239t
[06] > 00  00000000b  000t	[07] > 00  00000000b  000t
[08] > 01  00000001b  001t	[09] > 00  00000000b  000t
[0A] > 03  00000011b  003t	[0B] > 00  00000000b  000t
[0C] > EF  11101111b  239t	[0D] > 00  00000000b  000t
[0E] > 00  00000000b  000t	[0F] > 00  00000000b  000t
[10] > 00  00000000b  000t	[11] > 00  00000000b  000t
[12] > 00  00000000b  000t	[13] > FF  11111111b  255t
[14] > 03  00000011b  003t	[15] > 00  00000000b  000t
[16] > 00  00000000b  000t	[17] > 00  00000000b  000t
[18] > 00  00000000b  000t	[19] > 00  00000000b  000t
[1A] > 00  00000000b  000t	[1B] > C0  11000000b  192t
[1C] > F0  11110000b  240t
=q
=

=================================================