**** AGGREGATE FILE 76-38.txt  5/17/01 ****

===============================================================

    **** FILE 76B-38.txt ****

These SED1376 register contents were taken while
displaying a 240x320x4 image on a KHS038AA1AC
Kyocera LCD module.  The SED1376 was on an
SDU1376BOC evaluation board by Epson.

CONNECTIONS
  This board was mounted in a PCI slot, connected to
  a Kyocera KK5 No.2 interface board via 40pin cable.
  The 22 pin FPC lead of the Kyocera LCD was inserted
  into the connector of the KK5 labeled "CN5" on a
  White paper label. 

REGISTER CONFIGURATION  
  I made a copy of 1376BMP.EXE, renamed 76B-38.EXE
  and ran 1376CFG.EXE to configure it as follows:

 PANEL TAB
 (The following settings are absolutely required
 by the Kyocera KRS025EV LCD modules)
    color, format2, STN, 8bit, FPline Hi,
    FPframe Hi, 240 width, 320 height.

 (The following settings are interrelated and many
 different combinations are possible.  Section 5
 of the Kyocera spec gives the required ranges for
 frame rate and pixel clock.  Anytime you change
 a value, 1376CFG.exe may change some other value 
 to make your change possible.  Play with it until
 all values are satisfactory.  Here is what I ended
 up with.)
   Display Total H[pxl]=408 and V[line]=321,
   Display Start H[pxl]=22 and V[line]=0,
   Timings FrameRate=76 and PClk[kHz]=10000,
   FPLINE StartPos=0 and PulseWidth=8,
   FPFRAME StartPos=0 and PulseWidth=1,
   ColorDepth=4bpp, SwivelView=0,
   Predefined Panels shows "Custom Panel",
   Panel Invert has no check marks.

 CLOCKS TAB
 (I did not set anything under this tab.  The 
 values shown are the result of settings made 
 under the PANEL TAB.)
   CLKI is auto and 50000kHz is greyed out,
   BCLK Source and Divide is CLKI amd 1:1,
   PWMClk/CVPulse Source is CLKI,
   CLKI2 is auto and 10000 kHz is greyed out,
   MCLK Source and Divide is BCLK and 1:1,
   PWM has no checks and PWM Clk Div=1
       and Duty Cycle=0,
   Contrast Voltage has no checks and
       CV Pulse div=1 and CV Burst Len=1,  
   PCLK Source and Divide is CLKI2 and auto
       and 1:1 is marked and greyed out.
   
 OTHER TABS WERE NOT SET BY ME AND SEEMED TO 
 DEFAULT CORRECTLY TO MY PC'S PARAMETERS.

SAVING CONFIGURATION VALUES
 Run 1376CFG.exe under windows.  To get the initial
 values, open 1376BMP.exe or a copy of it, for
 example 76B-38.exe.  Then modify as above.  
   Then click "Save in..",
   highlight the same program you just opened, 
   click "Add>" to move it to the right hand screen, 
   click "configure" to write in the new values.  

OPERATING THE LCD
 Run the program renamed 76B-38.exe and configured 
 as above at the prompt on the MS-DOS emulation
 screen.  For example
    c:\...>76B-38 FL4-2432.bmp

 The 80K memory of the SED1376 allows 240x320x8
 images to be displayed, exactly filling the screen
 of the KHS038AA.   It will correctly display images 
 with 1 bpp color.  The color depth of 4 Bpp under 
 the PANEL tab seems to an initializing value, 
 that is properly superceeded by the color depth
 of the actual image being displayed.

REGISTER VALUES
 Below are the register contents resulting from
 this configuration, obtained by running 
 1376PLAY.exe at the MS-DOS, and entering 
 commands "xa", then "q".

     Robert Joslyn 3/23/2001  800-826-0527
==============================================

1376PLAY - test utility - version 1.02 (HAL 1.02)

=
[0000] 28 14 0B 00 00 03 00 00-00 00 00 00 E0 20 90 00 
[0010] D0 00 32 00 1D 00 00 00-40 01 00 00 3F 01 00 00 
[0020] 87 00 00 00 80 00 00 00-1F 00 00 00 00 00 00 00 
[0070] 02 00 00 00 00 00 00 00-1E 00 00 00 00 00 00 00 
[0080] 50 00 00 00 00 00 00 00-00 00 00 00 4F 00 00 00 
[0090] EF 00 00 00 00 00 00 00-00 00 00 00 00 00 00 00 
[00A0] 00 00 00 00 00 00 00 00-00 80 00 00 00 80 00 00 
[00B0] 00 00 00 00 00 00 00 00-00 00 00 00 00 00 00 00 

GCP Data Registers:
[0000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
[0010] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
=

========================================================================
    **** FILE 76B-389.txt ****

These SED1376 register contents were taken while
displaying a 320x240x4 image rotated 90 degrees
onto a KHS038AA1AC Kyocera LCD module.  The SED1376 
was on an SDU1376BOC evaluation board by Epson. 

The board and its SED1376 registers were configured 
exactly as described in 76B-38.txt

However this test was executed as

  c:\...>76B-38 FL4-3224.bmp /r90

The LCD was still 240x320.  76B-38.exe was still
configured as 240x320 with swivelView initially
set to zero.  But the image was 320x240 and 
swivelView was set to 90 degrees at execution.

Below are the register values during 
swivelView=90, for comparison with
76B-38.txt.

     Robert Joslyn 3/21/2001  800-826-0527
==============================================

1376PLAY - test utility - version 1.02 (HAL 1.02)

=
[0000] 28 14 0B 00 00 03 00 00-00 00 00 00 E0 20 90 00 
[0010] D0 00 32 00 1D 00 00 00-40 01 00 00 3F 01 00 00 
[0020] 87 00 00 00 80 00 00 00-1F 00 00 00 00 00 00 00 
[0070] 02 01 00 00 27 00 00 00-28 00 00 00 00 00 00 00 
[0080] 50 00 00 00 00 00 00 00-00 00 00 00 4F 00 00 00 
[0090] EF 00 00 00 00 00 00 00-00 00 00 00 00 00 00 00 
[00A0] 00 00 00 00 00 00 00 00-00 80 00 00 00 80 00 00 
[00B0] 00 00 00 00 00 00 00 00-00 00 00 00 00 00 00 00 

GCP Data Registers:
[0000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
[0010] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
=

====================================================================